That´s only with ZIMO

Functions that are unique or ahead of their time make the difference to "normal" products. Much is based on sophisticated software, the hardware plays its part: not geared to lowest cost, but to high quality and sustainability. Some of these ZIMO Specials are decoder-based, some are system-based, and some are based on system and decoders.

The ZIMO System

The ZIMO system components

The main components of the ZIMO system are:

The Starter Sets of the ZIMO System

The following sets are offered to get you started:

  • STARTCommand station MX10 + Controller MX33, CAN cable + power supply 320 W
  • STARTFUCommand station MX10 + Controller MX33FU (MiWi radio) + CAN cable + power sup. 320 W
  • STARTECFU Command station MX10EC + Controller MX33FU (MiWi radio) + CAN cable + power s. 320 W
  • STARTWMCommand station MX10 + power supply 320 W + Roco WLAN-Maus + router + accessory
  • STARTECWMCommand station MX10EC + power supply 320 W + Roco WLAN-Maus + router + accessory
  • STARTGCommand station MX10 + Controller MX33 + CAN cable + power supply 600 W
  • STARTGFUCommand station MX10 + Controller MX33FU (MiWi radio) + CAN cable + power sup. 600 W

 

The StEin modules (stationary equipment modules)

The StEin modulesare components of the digital control system, and are used together with a ZIMO command station (digital centre) of the MX10 series. All "stationary equipment" of a model railway layout can be connected to the StEin modules. This is track sections (with occupancy detection and loco-number recognition, full RailCom functionality, overcurrent/short circuit handling, ZIMO HLU), accessory articles (turnouts, signals, uncouplers), point detectors and position indicators (contact rails, photoelectric sensors, etc) as well as speakers (for platform announcements, and others).

The individual products of the ZIMO system  (list without small articles)

MX10 Command station (digital centre), DCC/MM, 12 + 8 A, CAN-Bus, XNET,USB, LAN, MiWi radio, etc.
MX10EC Command station (digital centre) in Economy-Ausführung, 12 A, sonst weitgehend wie MX10
NG300 power supply (also as additional unit) for MX10; 30 V DC, 10 A (320 W)
NG600 power supply (high performance) for MX10; 30 V DC, 20 A (600 W)
MX33 Controller MX33, tethered edition
MX33FU Controller MX33, MiWi radio or tethered, battery 2200 mAh, built-in charging unit
6POL...M 6-pole CAN bus cable ("normal" controller cable) in various lengths (see price list)
8POLA..M 8-pole CAN bus cable to connect to booster devices and StEin modules
STEIN88G Stationary equipment module "StEin" fully featured (8 track sections, 8 switches, etc.)
STEIN80G Stationary equipment module "StEin" partially featured (only 8 track sections)
STEINE8W StEin expansion board for 8 switches (coils, motor, EPL)
STEINE8S StEin expansion board for 8 servo motors
STEINE8G StEin expansion boards for 8 track sections (on economical outputs)
ICA16LP connection board on a I2C bus for 16 signal lights, with solder pads
ICA16KL connection board on a I2C bus for 16 signal lights, with screw terminals

 

RailCom is a trademark of Lenz Elektronik GmbH.

 Command station MX10

The Command station MX10 (Digital Centre)
MX33 Roco Wlan-Maus

Controller MX33              Roco WLAN-Maus

     

         StEin (Stationary Equipment module) StEin88V

 

Letzte Aktualisierung: 05.07.2024