Accessories for "small" decoders ("small" scales N to O)

2 Riegel zu je 10 Stück Konstantstromquellen für LEDs, abknickbar.

For constantly bright LEDs when using an energy storage device on the decoder. To be used instead of a series resistor. Up to 3 LEDs can be connected in series. Two different current ratings are available by bridging solder pads (see wiring diagram).

KOSL1

KOSL2

KOSL3

0.2 mA resp. 1 mA, max 35 V; 2x 10 pcs. à 6.2 x 3.6 x 1.1 mm

0,5 mA resp. 4 mA, max 35 V; 2x 10 pcs. à 6,2 x 3,6 x 1,1 mm

   2 mA, max 35 V resp. 8 mA, max 22 V; 2x 10 pcs. à 6,2 x 3,6 x 1,1 mm

M4000Z

modify vehicle

Amplifier module for a logic level output of a decoder. Most of the decoders have logic level outputs, additionally to the normal outputs. These logic level outputs can be switched between 0V (OFF) and 5V (ON) and can therefore not be loaded, but need an external amplifier. Most of the time, logic level outputs are alternately used as SUSI outputs (Clock&Data) and are activated by CV #124 Bit 7.  
Te M4000Z's output supplies 0.5V.

10m highly flexible stranded wire in colour of choice:

black (BK), white (WE), red (RE), blue (BE), gray (GY), orange (OE), yellow (YW), green (GN), brown (BN), purple/violet (VT)

for additional loco wiring, the same wires as used for the ZIMO decoders
Specification: total cross section 0.06 mm²,  11 cores (highly flexible).

FLEXL1000xx

1000 m highly flexible stranded wire in colour of choice:

black (BK), white (WE), red (RE), blue (BE), gray (GY), orange (OE), yellow (YW), green (GN), brown (BN), purple/violet (VT)

for additional loco wiring, the same wires as used for the ZIMO decoders
Specification: total cross section 0.06 mm²,  11 cores (highly flexible).

STIFT6

modify decoder

6-pole pin connector with a pitch of 1.27 mm (corresponding to the NEM651 connectors) to transform a standard wired decoder into a F-type (MX630 -> MX630F).

RSTECK

modify decoder

8-pole (2x4) pin connector with a pitch of 2.54mm (corresponds to NEM652 connectors) to transform a standard wired decoder into a R-type (MX630 -> MX630R).

BUCHS6

N decoder counterpart

6-pole socket connector with a pitch of 1.27 mm, as counterpart to decoders with a 6-pole pin connector (-N, -F) to make the decoder pluggable and thus changeable.

It is used with N-types or F-types, i.e. for decoders that are intended for locos with integrated 6-pole counterpart.

STIFT22

MTC-decoder counterpart

22-pole (2x11) pin connector with a pitch of 1.27 mm, as counterpart for decoders with a 22-pole socket connector ("MTC" also called 21-pole connector, i.e. C-types and D-types) to make the decoder pluggable in locos without interface, and is thus interchangeable easily.

It is used with C-types and D-types, i.e. decoders, which are intended for locos with integrated "MTC" counterpart.

BUCHS22

PluX decoder counterpart

22-pole (2x11) socket connector with a pitch of 1.27 mm as counterpart for decoders with a 22-pole or 16-pole PluX pin connector, to make the decoder pluggable into locos without interface and thus easily changeable.

It is used with -P16 and -P22 decoders, i.e. decoders for locos with integrated PluX connectors.

Note: this product consists - like all mentioned counterparts - for only one component, which has to be mounted by the user. A lot more comfortable is the solution with ADAPLU, ADAPLU15 or ADAPLU50, which provide large solder pads on the proper circuit board; see loco and adapter boards.

RAUSIH01

Smoke generator
PCB 

The RAUSIH01 board is used to control single smoke generators for H0 gauge (and small 0 gauge), together with ZIMO H0 gauge decoders. The RAUSIH01 can only be used if the smoke generator has a 100 kOhm NTC temperature sensor and a 20 to 33 Ohm heating element. The RAUSIH01 has a 5V regulator, which is why a small 5V motor can be connected as a smoke fan.
The RAUSIH01 can only be used with the MS450, MS440D, MN330, MN340D or MN300 decoders. Due to the current required by the heating element, the RAUSIH01 is not suitable for operation with miniature decoders.

Dimensions: 15.2 x 10 x 2.6 mm

ADAPLU
ADAPLU15
ADAPLU50
ADAMTC
ADAMTC15

see loco and adapter boards !